P4L 500 Full Range Monoblock Amplifier
The P4L 500 is a class D full range monoblock amplifier. This amplifier was engineered, tested, and produced in the USA. It features a completely bespoke power supply and output section design.
The Heatsink
Each aluminum heatsink is machined in Ohio, while the acrylic is laser cut and engraved at our facility in Michigan. All holes are drilled and tapped by hand at our facility as well. The heatsink was designed to keep the amplifier running cool, while keeping a lightweight profile. The center acrylic section allows for the PCB to be visible in a standard mounting position. It also allows for the amplifiers to be customized upon request. Each heatsink features 3D printed PETG end caps.
The Power Supply
The P4L 500 features a classic switch mode power supply design. At the heart of the power supply is a hand wound transformer using an oversized epoxy ferrite core. The transformer is ran by two pairs of mosfets, which are driven by single PNP transistors. Two 16 amp rectifiers are responsible for creating the DC rails for the output section. VCC is generated by an auxiliary winding on the transformer which is rectified by a pair of 1000v rated diodes. The power supply has a generous bank of rail capacitors to store energy for the output section. 80 amps of on-board fusing is used to protect the amplifier and your vehicle in the event of an overcurrent situation.
The Output Section
The output section of the P4L 500 Is a half bridge design focused around the IRS2092S driver. The driver runs four 200 volt, 76 amp rated mosfets at a switching frequency of 120khz. This allows the amplifier to play full range at high power levels efficiently, while staying away from the breakdown voltage of the components. The class D switching is filtered through a hand wound inductor using a Kool Mu core, and a 400v rated Wima film capacitor. An abundance of rail capacitors are placed near the output mosfets allowing the amplifier to make great dynamic power during transient notes.
The Filter Network
The simplistic filter network design allows the amplifier to have quality sound output with minimal points of failure. It uses a single op-amp to boost the input signal while using passive components for the high and low pass filters.
Testing and Development
The P4L 500 has been in development for over 15 months. During that time, the power supply and output section have gone through many revisions to refine the circuit as much as possible. Our circuit design has gone through extensive environmental, vibration, and load testing.
Amplifier Features:
4 gauge pure copper power input terminals.
8 gauge pure copper speaker output terminals.
Tiffany style RCA input
24db Fixed high pass filter at 80hz.
24db Fixed low pass filter at 100hz
Full range mode
11 volt - 15.5 volt input voltage. (higher voltage models available upon request)
20hz-20khz frequency response.
Green power LED (different colors available upon request)
Built in overcurrent protection
80 amps of onboard fusing
Replaceable aluminum mounting feet
Each amplifier we produce goes through a one hour endurance test to ensure it’s functionality.
Power Ratings at 14.4 volts:
4 ohm: 200 watts RMS x 1
2 ohm: 320 watts RMS x 1
1 ohm: 500 watts RMS x 1
Power Ratings at 15.5 volts:
4 ohm: 300 watts RMS x 1
2 ohm: 430 watts RMS x1
1 ohm: 650 watts RMS x1
Warranty Info:
Each amplifier comes with a one year limited warranty. This covers manufacturer, component, and material defects only. Improper installation and abuse is not covered under our warranty. The warranty only applies to the original purchaser. If you have any issues with your amplifier beyond the warranty period, please reach out to us through our repair request form and we will be happy to help.
The P4L 500 is a class D full range monoblock amplifier. This amplifier was engineered, tested, and produced in the USA. It features a completely bespoke power supply and output section design.
The Heatsink
Each aluminum heatsink is machined in Ohio, while the acrylic is laser cut and engraved at our facility in Michigan. All holes are drilled and tapped by hand at our facility as well. The heatsink was designed to keep the amplifier running cool, while keeping a lightweight profile. The center acrylic section allows for the PCB to be visible in a standard mounting position. It also allows for the amplifiers to be customized upon request. Each heatsink features 3D printed PETG end caps.
The Power Supply
The P4L 500 features a classic switch mode power supply design. At the heart of the power supply is a hand wound transformer using an oversized epoxy ferrite core. The transformer is ran by two pairs of mosfets, which are driven by single PNP transistors. Two 16 amp rectifiers are responsible for creating the DC rails for the output section. VCC is generated by an auxiliary winding on the transformer which is rectified by a pair of 1000v rated diodes. The power supply has a generous bank of rail capacitors to store energy for the output section. 80 amps of on-board fusing is used to protect the amplifier and your vehicle in the event of an overcurrent situation.
The Output Section
The output section of the P4L 500 Is a half bridge design focused around the IRS2092S driver. The driver runs four 200 volt, 76 amp rated mosfets at a switching frequency of 120khz. This allows the amplifier to play full range at high power levels efficiently, while staying away from the breakdown voltage of the components. The class D switching is filtered through a hand wound inductor using a Kool Mu core, and a 400v rated Wima film capacitor. An abundance of rail capacitors are placed near the output mosfets allowing the amplifier to make great dynamic power during transient notes.
The Filter Network
The simplistic filter network design allows the amplifier to have quality sound output with minimal points of failure. It uses a single op-amp to boost the input signal while using passive components for the high and low pass filters.
Testing and Development
The P4L 500 has been in development for over 15 months. During that time, the power supply and output section have gone through many revisions to refine the circuit as much as possible. Our circuit design has gone through extensive environmental, vibration, and load testing.
Amplifier Features:
4 gauge pure copper power input terminals.
8 gauge pure copper speaker output terminals.
Tiffany style RCA input
24db Fixed high pass filter at 80hz.
24db Fixed low pass filter at 100hz
Full range mode
11 volt - 15.5 volt input voltage. (higher voltage models available upon request)
20hz-20khz frequency response.
Green power LED (different colors available upon request)
Built in overcurrent protection
80 amps of onboard fusing
Replaceable aluminum mounting feet
Each amplifier we produce goes through a one hour endurance test to ensure it’s functionality.
Power Ratings at 14.4 volts:
4 ohm: 200 watts RMS x 1
2 ohm: 320 watts RMS x 1
1 ohm: 500 watts RMS x 1
Power Ratings at 15.5 volts:
4 ohm: 300 watts RMS x 1
2 ohm: 430 watts RMS x1
1 ohm: 650 watts RMS x1
Warranty Info:
Each amplifier comes with a one year limited warranty. This covers manufacturer, component, and material defects only. Improper installation and abuse is not covered under our warranty. The warranty only applies to the original purchaser. If you have any issues with your amplifier beyond the warranty period, please reach out to us through our repair request form and we will be happy to help.
The P4L 500 is a class D full range monoblock amplifier. This amplifier was engineered, tested, and produced in the USA. It features a completely bespoke power supply and output section design.
The Heatsink
Each aluminum heatsink is machined in Ohio, while the acrylic is laser cut and engraved at our facility in Michigan. All holes are drilled and tapped by hand at our facility as well. The heatsink was designed to keep the amplifier running cool, while keeping a lightweight profile. The center acrylic section allows for the PCB to be visible in a standard mounting position. It also allows for the amplifiers to be customized upon request. Each heatsink features 3D printed PETG end caps.
The Power Supply
The P4L 500 features a classic switch mode power supply design. At the heart of the power supply is a hand wound transformer using an oversized epoxy ferrite core. The transformer is ran by two pairs of mosfets, which are driven by single PNP transistors. Two 16 amp rectifiers are responsible for creating the DC rails for the output section. VCC is generated by an auxiliary winding on the transformer which is rectified by a pair of 1000v rated diodes. The power supply has a generous bank of rail capacitors to store energy for the output section. 80 amps of on-board fusing is used to protect the amplifier and your vehicle in the event of an overcurrent situation.
The Output Section
The output section of the P4L 500 Is a half bridge design focused around the IRS2092S driver. The driver runs four 200 volt, 76 amp rated mosfets at a switching frequency of 120khz. This allows the amplifier to play full range at high power levels efficiently, while staying away from the breakdown voltage of the components. The class D switching is filtered through a hand wound inductor using a Kool Mu core, and a 400v rated Wima film capacitor. An abundance of rail capacitors are placed near the output mosfets allowing the amplifier to make great dynamic power during transient notes.
The Filter Network
The simplistic filter network design allows the amplifier to have quality sound output with minimal points of failure. It uses a single op-amp to boost the input signal while using passive components for the high and low pass filters.
Testing and Development
The P4L 500 has been in development for over 15 months. During that time, the power supply and output section have gone through many revisions to refine the circuit as much as possible. Our circuit design has gone through extensive environmental, vibration, and load testing.
Amplifier Features:
4 gauge pure copper power input terminals.
8 gauge pure copper speaker output terminals.
Tiffany style RCA input
24db Fixed high pass filter at 80hz.
24db Fixed low pass filter at 100hz
Full range mode
11 volt - 15.5 volt input voltage. (higher voltage models available upon request)
20hz-20khz frequency response.
Green power LED (different colors available upon request)
Built in overcurrent protection
80 amps of onboard fusing
Replaceable aluminum mounting feet
Each amplifier we produce goes through a one hour endurance test to ensure it’s functionality.
Power Ratings at 14.4 volts:
4 ohm: 200 watts RMS x 1
2 ohm: 320 watts RMS x 1
1 ohm: 500 watts RMS x 1
Power Ratings at 15.5 volts:
4 ohm: 300 watts RMS x 1
2 ohm: 430 watts RMS x1
1 ohm: 650 watts RMS x1
Warranty Info:
Each amplifier comes with a one year limited warranty. This covers manufacturer, component, and material defects only. Improper installation and abuse is not covered under our warranty. The warranty only applies to the original purchaser. If you have any issues with your amplifier beyond the warranty period, please reach out to us through our repair request form and we will be happy to help.